Revelation Front Of Center Outsert System F.O.C.O.S Patented
Front Of Center Outsert System (Patent #US10203185)
Quantity per pack:: 12 each
Quantity per pack:: 12 each
The Revelation Front Of Center Outsert System (F.O.C.O.S.), patented andted and manufactured by the renowned Black Eagle brand, is a game-changer in the Black Eagle Arrow Components category. Crafted from high-quality metal types such as stainless steel, 7075 T6 aluminum, aluminum, and black nitride steel, this outsert system is designed to elevate your arrow performance. With Revelation FOCOS Outserts available in 300 spine, 350 spine, and 400 spine, this product ensures precise weight distribution for better accuracy and increased kinetic energy delivery. Experience enhanced performance and unmatched durability with the Black Eagle Revelation Front Of Center Outsert System (F.O.C.O.S.) patented.
The F.O.C.O.S. is made of 3 parts. One is the black anodized 7075 T6 aluminum alloy outsert or stainless steel option. Two are stainless steel retention posts in the aluminum outsert model and aluminum in the stainless steel outsert model that also acts as a footer inside the shaft. The third part is the 3/32 allen head retention screw that allows for the outserts to either be screwed or screwed and glued. (Not Tattooed) This system has been tested to over 550 pounds per square inch of pull, and they stay on! If you are looking for maximum penetration, maximum F.O.C., and shot-after-shot performance, then the F.O.C.O.S are sure to be a hit!
Insertion Depth of Arrow in Outsert is .610, almost 5/8"
The outsert adds Approximately 1.090" to end of the arrow.
Insertion Depth of Arrow in Outsert is .610, almost 5/8"
The outsert adds Approximately 1.090" to end of the arrow.
The Revelation Outsert Weights are as follows:
ALUMINUM OUTSERTS' TOTAL WEIGHT
ALL SPINES WEIGH 80 GRAINS.
STAINLESS STEEL OUTSERTS: TOTAL WEIGHT
ALL SPINES WEIGH 100 GRAINS.
ALUMINUM OUTSERTS' TOTAL WEIGHT
ALL SPINES WEIGH 80 GRAINS.
STAINLESS STEEL OUTSERTS: TOTAL WEIGHT
ALL SPINES WEIGH 100 GRAINS.
- To install the F.O.C.O.S. system
- Select the right outsert for the right shaft.
- Glue in Stainless steel retention Post
- Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
- If Outserts does not fit, that is OK. Get some 100 grit sandpaper and lightly sand the shaft in a circular motion until the outsert fits fairly snug on the shaft. Start slowly so you don't remove too much of the arrow.
- You should have approximately 3/4 of an inch insertion on aluminum outserts.
- Wipe dust off of the shaft with a clean paper towel. (No Cleaners are recommended.)
- Again, spin test to ensure concentricity.
- Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment
- Slide the outsert over the shaft and use the 3/32 head retention screw and lock the outsert in place!
- If using glue, see steps 11-15.
- We have tested our fletching glue, insert/outsert glue, and epoxy, and all of them work great.
- Apply a even amount of glue around the shaft to ensure you get enough glue in them to hold.
- Slide the outsert on the shaft, rotating to make sure the glue/epoxy is evenly dispersed
- Use the 3/32 head retention screw and lock the outsert in place! Loctite Purple or Blue recommended
- Once the outsert is glued on, the screw is installed. Stand the arrow on the nock end to dry.
No reviews
