The Rampage Front Of Center Outsert System F.O.C.O.S (Patented) is a revolutionary product in the Components category. This outsert system is designed to improve the performance and accuracy of arrows by shifting the weight forward to enhance front-of-center balance. Its patented design ensures superior durability and easy installation. By optimizing the F.O.C.O.S system, this product guarantees enhanced arrow flight and accuracy, making it a must-have for serious archers.
The F.O.C.O.S is made of 3 parts. One is a black anodized 7075 T6 aluminum alloy outsert. Two is a Stainless steel Retention post that also acts as a footer inside the shaft. The third part is the 3/32 allen head retention screw that allows for the Outserts to either be screwed on or screwed and glued.(Not Tattooed) This system has been tested to over 550 Pounds per square inch of pull and they stay on! If you are looking for maximum penetration, Maximum F.O.C and shot after shot performance then the deadly combination of the Rampage arrows then the F.O.C.O.S is sure to be a hit!
Rampage F.O.C.O.S Outserts use FOCOS Brass Weights if you are adding extra weight
- To install the F.O.C.O.S System
- Select the right outsert for the right shaft.
- Glue in Stainless steel retention Post
- Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
- If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits fairly snug on shaft. Start slowly so you don't remove to much off the arrow.
- You should have approximately 3/4 of an inch insertion on Aluminum Outserts
- Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
- Again, Spin test to ensure concentricity.
- Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment
- Slide outsert over shaft and use the 3/32 Head retention Screw and Lock the Outsert in place!
- If using glue See steps 11-15 .
- We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
- Apply a even amount of glue around the shaft to ensure you get enough glue in them to hold.
- Slide Outsert On shaft rotating to make sure Glue/Epoxy is evenly dispersed
- Use the 3/32 Head retention Screw and Lock the Outsert in place! Loctite Purple or Blue recommended
- Once The outsert is glued on Screw is installed stand the arrow on the nock end to dry.
39 Reviews
-
Quality
So far we have really liked the quality and durability of your products!
-
Shipping
Would Like to get some sort of tracking for this delivery. I get a email stating order was received, but haven't received a tracking number or have I seen the parts show up.
-
Shipping sucks
Haven’t gotten them yet they were supposed to be here on the 24 the only thing that usps has said for the last 3 days is arriving late but still on its way
-
buying more going forward!
Yes this product adds FOC to the arrow, but the main reason I wanted it was to add strength to the impact side of my arrow. I love how the system encases the arrow to help create that extra strength internally and externally, plus the system in general an easy install.
-
Needs some work...
Ok, I wanted to give this five stars but I accidentally broke two of the black inserts trying to get them onto the arrows. So that stinks :(. The fit was way too tight. The arrows they did fit on are great. You really need to have instructions printed on the label or included in the packaging. I found them on website after I had the misshaps. But since it came with no instruction, I was like "oh, this is that easy? Cool!"
-
Customer review
Review body is empty
-
Rampage
Great Idea but in reality not so great. The screw holding the sleeve will always come loose. Just not a good fit for my set up. I will just use the half out inserts with weights.
-
Great System with Durability
The FOCOS system is the best outsert system out there. Extremely durable and allows you to fix a damaged component with out losing an arrow. With the arrows, these are made very consistent at high tolerances. Big win for Black Eagle.
-
Awesome
Got my order earlier than expected.
-
Customer review
Perfect fit!!
-
Customer review
Never tried this product, they seem like a good design with the set screw to replace the sleeve in case of damage. The only thing i have to complain about is they are aluminum which isnt as strong as stainless steel.
-
Customer review
Review body is empty
