The Rampage Front Of Center Outsert System F.O.C.O.S (Patented) is a revolutionary product in the Components category. This outsert system is designed to improve the performance and accuracy of arrows by shifting the weight forward to enhance front-of-center balance. Its patented design ensures superior durability and easy installation. By optimizing the F.O.C.O.S system, this product guarantees enhanced arrow flight and accuracy, making it a must-have for serious archers.
The F.O.C.O.S is made of 3 parts. One is a black anodized 7075 T6 aluminum alloy outsert. Two is a Stainless steel Retention post that also acts as a footer inside the shaft. The third part is the 3/32 allen head retention screw that allows for the Outserts to either be screwed on or screwed and glued.(Not Tattooed) This system has been tested to over 550 Pounds per square inch of pull and they stay on! If you are looking for maximum penetration, Maximum F.O.C and shot after shot performance then the deadly combination of the Rampage arrows then the F.O.C.O.S is sure to be a hit!
Rampage F.O.C.O.S Outserts use FOCOS Brass Weights if you are adding extra weight
- To install the F.O.C.O.S System
- Select the right outsert for the right shaft.
- Glue in Stainless steel retention Post
- Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
- If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits fairly snug on shaft. Start slowly so you don't remove to much off the arrow.
- You should have approximately 3/4 of an inch insertion on Aluminum Outserts
- Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
- Again, Spin test to ensure concentricity.
- Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment
- Slide outsert over shaft and use the 3/32 Head retention Screw and Lock the Outsert in place!
- If using glue See steps 11-15 .
- We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
- Apply a even amount of glue around the shaft to ensure you get enough glue in them to hold.
- Slide Outsert On shaft rotating to make sure Glue/Epoxy is evenly dispersed
- Use the 3/32 Head retention Screw and Lock the Outsert in place! Loctite Purple or Blue recommended
- Once The outsert is glued on Screw is installed stand the arrow on the nock end to dry.
39 Reviews
-
Customer review
Review body is empty
-
Customer review
Review body is empty
-
Awsome quality can't beat the value
Very well made and high quality outserts perfect for gaining FOC and making your arrow tougher!! Every one of them spun perfect and they were super easy to install.
-
Best outsert on the market
The FOCOS outserts are awesome you glue in the insert slip the sleeve over the end of the shaft and tighten the screw. You can replace the sleeve if you damage it without removing the glued in insert which is awesome. Spins straight and adds 100 grains to the front of the arrow. Can’t get any better.
-
Great service and excellent component
This is by far my favorite system for stiffening the front when using heavier heads for my trad set up.
-
Excellent service and arrows
There is a reason someone from South Carolina / Colorado orders his arrows from Oregon, it's simply the best I can find.
-
F.O.C.O.S
Very easy to install and make the rampage 250s absolute pile drivers
-
Arrow Armour
The FOCOS system is simple to use and gives you excellent arrow protection and killer front of center!
-
Customer review
Review body is empty
-
Customer review
Review body is empty
-
Checkout didn't work for me
For some reason when I went to check out my card declined 3 times and I got 3 pending charges. I used 3 different cards. I finally just used PayPal to get it to work.
-
Great product
Love Black eagle arrows, and their Front of center system is the best on the market. Best arrows for the price.
