Quantity per pack 12
Introducing the X-Impact Front Of Center Outsert System F.O.C.O.S (Patented) by Black Eagle. This revolutionary product is designed to enhance the performance of your arrow components. Made with high-quality materials like stainless steel and 7075 T6 aluminum, it offers unmatched durability and strength. Elevate your archery game with the X-Impact Front Of Center Outsert System F.O.C.O.S (Patented) by Black Eagle.
The F.O.C.O.S is made of 3 parts. One is the black anodized 7075 T6 aluminum alloy outsert or Stainless Steel Option. Two is a Stainless steel Retention post In The Aluminum Outsert Model and Aluminum in the Stainless Steel Outsert Model that also acts as a footer inside the shaft. The third part is the 3/32 allen head retention screw that allows for the Outserts to either be screwed or screwed and glued.(Not Tattooed) This system has been tested to over 550 Pounds per square inch of pull and they stay on! If you are looking for maximum penetration, Maximum F.O.C and shot after shot performance then the deadly combination of the Deep Impact, Instinct or X-Impact shafts then the F.O.C.O.S are sure to be a hit!
Insertion Depth of Arrow in Outsert is .610 almost 5/8"
Outsert adds Approximately 1.090" to end of the Arrow
ALUMINUM OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 80 Grains
STAINLESS STEEL OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 100 Grains
- To install the F.O.C.O.S System
- Select the right outsert for the right shaft.
- Glue in Stainless steel retention Post
- Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
- If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits fairly snug on shaft. Start slowly so you don't remove to much off the arrow.
- You should have approximately 3/4 of an inch insertion on Aluminum Outserts
- Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
- Again, Spin test to ensure concentricity.
- Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment
- Slide outsert over shaft and use the 3/32 Head retention Screw and Lock the Outsert in place!
- If using glue See steps 11-15 .
- We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
- Apply a even amount of glue around the shaft to ensure you get enough glue in them to hold.
- Slide Outsert On shaft rotating to make sure Glue/Epoxy is evenly dispersed
- Use the 3/32 Head retention Screw and Lock the Outsert in place!
- Once The outsert is glued on Screw is installed stand the arrow on the nock end to dry.
43 Reviews
-
clever system
i wish the weights were adjustable before inserts were glued in, but the system itself works as advertised and really lets you dial in FOC.
-
Great
Perfect system for good FOC and aligning broadheads to vanes!!
-
I’m an idiot!
I recently purchased a Dz bare shafts and about an hour later realized I had ordered the wrong spine. I called in and spoke with someone in sales stating what I had done and could this be changed. His answer was, “Looks like your order has already been fulfilled, but if the truck hasn’t come yet we will get them switched out.” First of all, fulfilling an order an hour after being placed is incredible. Secondly, I got the correct spine shafts delivered a couple days later! Thank you Blackeagle for amazing products and unmatched customer service! My Rampage shafts have been built into arrows and are awaiting range day. They seem to be a great product so far. We’ll see how they fly tomorrow.
-
Customer review
Review body is empty
-
Black Eagle Service
Have always received speedy service from BE. Never an issue. However, can't say the same for USPS. Anything shipped on them is still a coin flip. At the time of this review I still haven't received these outserts.
-
SMACK
Great product. Easy to install and really adds consistency and accuracy to my setup.
-
Stainless steel outsert
Wow, what a difference these make, great way to help control weight and make an already tuff arrow nearly Indestructible
-
FOCOS System
Easy to install, light sanding required for a few of the impact collars, very satisfied.
-
F.O.C.O.S outsert system
This system is hands down the best I have used. You can align your broadheads if you wish if mess one up rock/tree etc. screw on a new one and be on your way. Very innovative
-
Very good outserts and online experience
Have been using these outserts for about a year. Shopping experience is good/quick and delivery was very fast. Thanks
-
Tip weight
Great system! I highly recommend it
-
FOCUS INSERT/OUTSERT
Recently built a set of Black Eagle X Impact 250 Spine with 80G FOCUS SYSTEM. Awesome product! Durable, Spins True, Amazing FOC. Throwing 100G QAD Exodus Head on them....Hits like a Hammer. Excited for elk season here in WA.
