Front Of Center Outsert System (Patent#US10203185)
X Impact Front Of Center Outsert System F.O.C.O.S (Patented)
Introducing the X-Impact Front Of Center Outsert System F.O.C.O.S (Patented) by Black Eagle. This revolutionary product is designed to enhance the performance of your arrow components. Made with high-quality materials like stainless steel and 7075 T6 aluminum, it offers unmatched durability and strength. Elevate your archery game with the X-Impact Front Of Center Outsert System F.O.C.O.S (Patented) by Black Eagle.
The F.O.C.O.S is made of 3 parts. One is the black anodized 7075 T6 aluminum alloy outsert or Stainless Steel Option. Two is a Stainless steel Retention post In The Aluminum Outsert Model and Aluminum in the Stainless Steel Outsert Model that also acts as a footer inside the shaft. The third part is the 3/32 allen head retention screw that allows for the Outserts to either be screwed or screwed and glued.(Not Tattooed) This system has been tested to over 550 Pounds per square inch of pull and they stay on! If you are looking for maximum penetration, Maximum F.O.C and shot after shot performance then the deadly combination of the Deep Impact, Instinct or X-Impact shafts then the F.O.C.O.S are sure to be a hit!
Insertion Depth of Arrow in Outsert is .610 almost 5/8"
Outsert adds Approximately 1.090" to end of the Arrow
The Deep Impact & X-Impact Outsert Weights are a Follows:
ALUMINUM OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 80 Grains
STAINLESS STEEL OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 100 Grains
- Select the right outsert for the right shaft.
- Glue in Stainless steel retention Post
- Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
- If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits fairly snug on shaft. Start slowly so you don't remove to much off the arrow.
- You should have approximately 3/4 of an inch insertion on Aluminum Outserts
- Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
- Again, Spin test to ensure concentricity.
- Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment
- Slide outsert over shaft and use the 3/32 Head retention Screw and Lock the Outsert in place!
- If using glue See steps 11-15 .
- We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
- Apply a even amount of glue around the shaft to ensure you get enough glue in them to hold.
- Slide Outsert On shaft rotating to make sure Glue/Epoxy is evenly dispersed
- Use the 3/32 Head retention Screw and Lock the Outsert in place!
- Once The outsert is glued on Screw is installed stand the arrow on the nock end to dry.
43 Reviews
-
Great system
Very common-sense system that works great for those who want a higher front of center. Good quality.
-
A+++
Quick Shipping, Great as always!!
-
Focus outserts
Havent used them yet. But am super excited to switch from the victory outsert to this system. One thing right off the bat, i wish the insert shelf and the hex pin shelf were wider to have more surface contact. But all in all we’ll see.
-
Great system.
Awesome system. Supper strong and easy to use. Wish it was marketed better took a little research to find but very glad I did.
-
Black eagle SS outserts
Great product - very easy to install and set up true . Shoot perfect
-
Don’t Spin True
Tried the new outsert and can’t get them to spin true. Meticulously squared the cut shaft, glued in the insert portion, and no matter how much you dry fit and rotate them, about 1 in 4 spin true. I’d go back to a .204” ID system if I could do it over again. Not worth going to micro diameter if you have to use deep six or these.
-
Great system
Offers ability to load up weight or keep it at a moderate point weight. You can really dial in an arrow setup. I wasn't so sure about the retention screw idea but in use it has been perfectly solid. Bonus to this system is being able to loosen outsert and obtain broadhead alignment. Pretty simple system to use once you put a few together, tolerances are very tight and accurate.
